MAGIC OF SCIENCE
TODAY I WILL TELL YOU HOW TO GENERATE ELECTRICITY USING BAR MAGNET .
MATERIAL REQUIRED: UNCOVER WIRE , A BAR MAGNET ,WOODEN BLOCK , A LONG IRON NAIL(ABOUT 15 CM),A ROLLED LIKE STRUCTURE
INSULATOR (YOU CAN TAKE A PAPER ROLL), A DRILLER , FEVICOL, A BULB.
BASIC PRINCIPLE: ELECTROMAGNETIC INDUCTION WAS FIRST DISCOVER BY MICHAEL FARADAY, WHO MADE HIS DISCOVERY IN 1831, NOW WE ARE MOVING TO THE BASIC CONCEPT OF THE EXPERIMENT .WHEN THE MAGNET IS IN ITS STATIONARY POSITION THEN ,ITS GENERATE A MAGNETIC FIELDS,AROUND ITS, WHEN WE START SPINNING THE UNCOVER COPPER WIRE,THE WIRE CONTINUOUSLY CUTS THE MAGNETIC FIELD LINE AND HENCE THE MECHANICAL ENERGY CONVERTS IN TO ELECTRICAL ENERGY.MORE WE SPIN GREATER
IS THE AMOUNT OF ELECTRICITY.
PROCEDURE:
STEP 1. BUILD A "U" SHAPED FRAME TO SUPPORT YOUR "ROTOR", IE, THE PERMANENT BAR MAGNET MOUNTED ON A STEEL SHAFT.
STEP 2.DRILL TWO 1⁄4 INCH (0.6 CM) HOLES IN THE TWO UPRIGHTS OF YOUR FRAME, ALIGNING THEM SO THAT THE 1⁄4 INCH (0.6 CM) ROD, (THE ROTOR SHAFT) WILL GO THROUGH BOTH WITHOUT BINDING.
STEP 3.DRILL A 1⁄4 INCH (0.6 CM) HOLE THROUGH THE CENTER OF YOUR BAR MAGNET, ON THE FLAT, OR WIDEST SIDE .
STEP 4.SLIDE THE METAL SHAFT THROUGH ONE SIDE OF THE SUPPORT FRAME, SLIDE THE MAGNET ONTO THE SHAFT.
STEP 5.CUT A 4 INCH (10.2 CM) SECTION OF THE PAPER(ROLLED LIKE STRUCTURE INSULATOR).
TODAY I WILL TELL YOU HOW TO GENERATE ELECTRICITY USING BAR MAGNET .
MATERIAL REQUIRED: UNCOVER WIRE , A BAR MAGNET ,WOODEN BLOCK , A LONG IRON NAIL(ABOUT 15 CM),A ROLLED LIKE STRUCTURE
INSULATOR (YOU CAN TAKE A PAPER ROLL), A DRILLER , FEVICOL, A BULB.
BASIC PRINCIPLE: ELECTROMAGNETIC INDUCTION WAS FIRST DISCOVER BY MICHAEL FARADAY, WHO MADE HIS DISCOVERY IN 1831, NOW WE ARE MOVING TO THE BASIC CONCEPT OF THE EXPERIMENT .WHEN THE MAGNET IS IN ITS STATIONARY POSITION THEN ,ITS GENERATE A MAGNETIC FIELDS,AROUND ITS, WHEN WE START SPINNING THE UNCOVER COPPER WIRE,THE WIRE CONTINUOUSLY CUTS THE MAGNETIC FIELD LINE AND HENCE THE MECHANICAL ENERGY CONVERTS IN TO ELECTRICAL ENERGY.MORE WE SPIN GREATER
IS THE AMOUNT OF ELECTRICITY.
PROCEDURE:
STEP 1. BUILD A "U" SHAPED FRAME TO SUPPORT YOUR "ROTOR", IE, THE PERMANENT BAR MAGNET MOUNTED ON A STEEL SHAFT.
STEP 2.DRILL TWO 1⁄4 INCH (0.6 CM) HOLES IN THE TWO UPRIGHTS OF YOUR FRAME, ALIGNING THEM SO THAT THE 1⁄4 INCH (0.6 CM) ROD, (THE ROTOR SHAFT) WILL GO THROUGH BOTH WITHOUT BINDING.
STEP 3.DRILL A 1⁄4 INCH (0.6 CM) HOLE THROUGH THE CENTER OF YOUR BAR MAGNET, ON THE FLAT, OR WIDEST SIDE .
STEP 4.SLIDE THE METAL SHAFT THROUGH ONE SIDE OF THE SUPPORT FRAME, SLIDE THE MAGNET ONTO THE SHAFT.
STEP 5.CUT A 4 INCH (10.2 CM) SECTION OF THE PAPER(ROLLED LIKE STRUCTURE INSULATOR).
STEP 6.WIND THE COPPER WIRE AROUND THE PAPER TUBE, LEAVING ABOUT 16 TO 18 INCHES (40.6 TO 45.7 CM) OF WIRE LOOSE ON EACH END TO CONNECT TO YOUR POWER TEST DEVICE, AN ELECTRIC LIGHT BULB, OR OTHER DEVICE YOU WILL SUPPLY POWER TO.
STEP 6.WIND THE COPPER WIRE AROUND THE PAPER TUBE, LEAVING ABOUT 16 TO 18 INCHES (40.6 TO 45.7 CM) OF WIRE LOOSE ON EACH END TO CONNECT TO YOUR POWER TEST DEVICE, AN ELECTRIC LIGHT BULB, OR OTHER DEVICE YOU WILL SUPPLY POWER TO.
STEP 7. SLIDE THE TUBE OVER THE SHAFT AND MAGNET, THEN SLIDE THE SHAFT ON THROUGH THE OTHER SUPPORT FRAME.
STEP 7. SLIDE THE TUBE OVER THE SHAFT AND MAGNET, THEN SLIDE THE SHAFT ON THROUGH THE OTHER SUPPORT FRAME.
STEP 8. SLIDE THE TUBE OVER THE SHAFT AND MAGNET, THEN SLIDE THE SHAFT ON THROUGH THE OTHER SUPPORT FRAME.
STEP 9. SUPPORT THE PAPER CYLINDER WITH THE WIRE WINDING AT THE CENTER OF THE SHAFT WITH THE BAR MAGNET CENTERED ON THE WIRE WINDING.
STEP 10. TURN THE SHAFT WITH YOUR FINGERS TO SEE IF THE ENDS OF THE MAGNET HIT THE INSIDE OF THE TUBE.
STEP 11. ATTACH THE TWO WIRES YOU HAVE LOOSE AT THE ENDS OF THE WINDING TO A FLASHLIGHT BULB OR OTHER LOW VOLTAGE LAMP.
STEP 12. SPIN THE SHAFT AS FAST AS POSSIBLE.
RESULT: YOU WILL FIND THAT THE BULB IS GLOWING THAT MEANS ELECTRICITY HAVE BEEN PRODUCED USING BAR MAGNET .
SAVE FUEL SAVE EARTH .USE MORE ECO FRIENDLY TECHNOLOGY TO GENERATE ELECTRICITY AT HOME.
some INTERESTING video:
RESULT: YOU WILL FIND THAT THE BULB IS GLOWING THAT MEANS ELECTRICITY HAVE BEEN PRODUCED USING BAR MAGNET .
SAVE FUEL SAVE EARTH .USE MORE ECO FRIENDLY TECHNOLOGY TO GENERATE ELECTRICITY AT HOME.
some INTERESTING video:
